How To Clean Foam Brush After Polyurethane
eight Answers 8
I have had trouble cleaning them with everything and had the same problem, until I found a jar large plenty to put the brush in filled to the bristle level with thinner keeping it tightly sealed. (I do clean them prior to putting in the jar). When I demand them take out shake dry and they work similar new brushes for months without being used or when I accept a projection that gets a new coat every day for a week. (I find the higher quality brushes provide the all-time coverage then I detest to toss them with just one use)
answered Dec 4, 2015 at 0:24
Ed BealEd Beal
93.3k 4 gold badges 64 silverish badges 135 bronze badges
vii
I make picture frames and I like polyurethane because information technology is a very hard, durable finish. I always use foam brushes. To clean I merely soak in paint thinner a short time shake it out and dry with a paper towel. You tin do this over and over if y'all want. But at around twenty five cent for a brush you lot could but toss them. And they leave a dainty even coat too.
answered Jun 26, 2019 at 3:43
one
-
Hello, and welcome to Home Improvement. Thanks for the respond; keep 'em coming. And, yous should probably take our bout so you'll know how best to contribute here.
Jun 26, 2019 at 13:21
since there are water based polyurethanes that you can clean up with water, you tin apply those. notwithstanding, kickoff with a good quality brush. if you want to use an alkyd, clean (thoroughly - not just a dunk) with paint thinner (takes the pigment into solution and flushes it away), so with acetone (takes the thinner into solution and flushes it away), and then with water (takes the acetone into solution and flushes it away as well as acting equally a solvent for the lather). and then rub the bristles in mitt bar soap (i like ivory manus soap for this). the brush volition stay squeamish and soft and supple. when you want to use information technology over again, just chop-chop dunk information technology in whatever solvent is the solvent in whatsoever paint you desire to employ. you lot tin can keep a quality brush going for years with this approach.
answered December 4, 2015 at 2:38
I've done all of the above - But I read that putting a fiddling clothes softener in with the paint thinner also keeps the bristles very soft ! I have tried this and it does piece of work !
answered May 7, 2018 at 17:37
$14 Purdy or Wooster brushes are trash later applying poly. Utilize cheaper disposable foam applicators.
answered Aug 2, 2018 at 1:33
Maybe not politically correct merely I found a quick dunk & swoosh in gasoline works better then any paint thinner or solvent. After dunking, I squeeze out what I tin by mitt & then apply liquid dish soap (like dawn) & piece of work into the bristles to remove the gas. Rinse in hot h2o & let to dry out. I find that placing a rubber band on it helps to keep shape.
answered Mar 27, 2021 at sixteen:48
3
-
What does that accept to do with political correctness?
Mar 27, 2021 at sixteen:49
-
@amphibient gasoline isn't a good choice for a solvent due to the hazards involved (the flashpoint is awful low, for 1)
Mar 27, 2021 at 17:04
-
If yous're going to do this, practice this OUTSIDE and Abroad from potential ignition sources. Gasoline'southward flashpoint is well into the negatives, and the vapors are "have passport, will travel to ignition source beneath you!"
Mar 27, 2021 at 17:05
I used paint stripper followed by soap and water and it worked well. A bristle comb helps (for paint brushes).
answered Mar 24, 2021 at 21:ten
Anyone try putting the brush in the freezer subsequently you rinse with pigment thinner? My grandpa use to tell me this worked.
answered Mar 27, 2021 at 21:18
Not the respond y'all're looking for? Browse other questions tagged paint cleaning or ask your own question.
Source: https://diy.stackexchange.com/questions/79304/how-to-clean-brush-after-polyurethane
Posted by: freemanstromend75.blogspot.com
If yous don't need information technology soon, how long do you keep it in ?
Dec 4, 2015 at 1:21
I have had them in the jar for over 6 months. The thinner has non affected them that I tin tell. My broad brush is ~3 years sometime the narrow ones maybe 2 years old.(I only take them out to use them now)
Dec four, 2015 at 14:12
that worked actually, really well, thank you. I just kept 3 brushes in a can overnight, much better.
December 5, 2015 at 0:10
You said "(I do clean them prior to putting in the jar)". What does that mean? How do you clean them prior to storage?
Jul viii, 2017 at 22:28
Past cleaning before I ordinarily squeeze the majority of the paint or other poly solids out of the brush then 1 rince to remove the bulk of the solids th3n put the brush in bristles deep thinner and seal it. With poly that I may be continuing work within a week I may non clear every bit much simply continue the bristles in thinner. Shake the excess thinner out and the brush is ready for another coat.
Jul 9, 2017 at twenty:32